Wheelchair Accessories General

Results: 249

3Rd Hand Small Electronics Mount

The 3rd Hand Small Electronics Mount is an extension arm for wheelchair accessories designed for use by individuals with mobility or neurological disabilities or spinal cord injury. The standard mount comes with a three-segment support arm, a ball base for attachment to the wheelchair or other surface, and a head plate surface for holding small electronics such as a cell phone, iPod, camera, PDA, miniPC, or adaptive switches. The head plate has an AMPS-NEC compatible head plate hole pattern. Ite

Accessory Mounting Platforms & Hardware

The Accessory Mounting Platforms and Hardware are adjustable wheelchair mounting kits for communicators. These aluminum mounting systems have a 2.5 x 8.5 inch platform and adjust through 360 degrees. Options include a flexible or pedestal mount, and flange, tube clamp, or tray clip.

Active Wheelchair Platform Rocker

The Active Wheelchair Platform Rocker is a rocking attachment for a wheelchair designed for use by individuals with mobility or neurological disabilities, Alzheimer's disease, or spinal cord injury. This unit is designed to enable an individual to experience the benefits of rocking without transfering from a wheelchair. The rocker features an entry/exit rear ramp, adjustable front caster stops to center the wheelchair on the platform, and two safety wheelchair tie-down straps. The Active Platfo

Adalap

The ADALAP is a lap desk designed for use by individuals who use wheelchairs. The basic unit includes the base and pole with a top plate with a Velcro loop. Made from lightweight anodized aluminum alloy with stainless steel fasteners, the unit has a base that slides right under the wheelchair seat cushion. Height adjustment is accomplished with a quick-release clamp.OPTIONS: Fresh or salt water fishing rod holder; Snap Lap Desk; Lap Shopper shopping basket; lap tray; accessory mount for camera,

Afterburner Wheel Chair Pusher

The Afterburner Wheel Chair Pusher is a cycle attachment for the wheelchair designed to transport a person in a wheelchair without having to transfer her or him from the wheelchair, and to provide outdoor entertainment for individuals who use a wheelchair. The back portion of the Afterburner looks like a normal bicycle with a rear wheel, seat and pedals; however there is no front wheel or handle bars. The front of the device is designed to attach to the back of a wheelchair (included). The After

Alert Light

The Alert Light is a safety flag designed for use with manual wheelchairs, power wheelchairs or scooters. It is intended to improve the visibility of the wheelchair or scooter during the day or night. The Alert Light consists of a pennant-shaped flag has a folding shaft that enables the flag to fold below the user's head when entering and exiting vehicles or when not in use. The upper portion of the shaft has a light emitting diode (LED) light that can be set as an orange glow or a flashing str

Alimed Aerocell Ii Pressure Relieving Wheelchair Cushions

The Alimed Aerocell II is a wheelchair cushion cover designed for individuals at risk of developing pressure sores. The cushion distributes pressure for even positioning for a more relaxed and comfortable sitting experience. The device is made out of black stretch nylon and its cover is washable. DIMENSIONS: Standard size is 18 inches length x 20 inches width x 4 inches depth. CAPACITY: 440 pound capacity. WEIGHT: 3.5 pounds. COLOR: Black. WARRANTY/GUARANTEE: As stated by the manufacturer.

Alimed E-Z Release Seat Belt With Alarm

The AliMed E-Z Release Seat Belt with Alarm is a wandering patient system designed for use by individuals with Alzheimer's disease or other cognitive disabilities who are at risk for falls in homes or hospitals. This seatbelt is equipped with a standard sensor unit (included) and a hook and loop fastening buckle that, once disengaged, alerts a caregiver or hospital staff that a person is about to wander or risks a fall. The sensor alarm can be attached to regular chairs, geri chairs, wheelchair

Anti-Tipping Bracket (Models 85F & 85R)

The Anti-Tipping Bracket is an anti-tipping lever designed for use on wheelchairs. The device consists of a pair of curved tubes, each with a small roller wheel, that attach to the wheelchair frame. Model 85F extends beyond the front caster to prevent forward tipping of the wheelchair. Model 85R extends from the back of the chair to prevent rear tipping.

Auto Style Hip Belt (Model Ee 3D/103-6000)

Wheelchair seat belt, nylon webbing and auto style push button buckle. Has a pair of iliac crest relief pads so the the belt may be cinched tightly without causing pressure on the bony prominences. Should be mounted at a 45í angle to the seat.

Bi-Fold Sensor Pad For Chair And Bed

The Bi-Fold Sensor Pad is a discrete sensor that alerts a caregiver when their patient has fallen from their bed or chair. This dual purpose sensor pad can be folded. In it’s folded format the pad measures 15 inches wide x 15 inches long and can be placed on the wheelchair either above or below the seat cushion. In the unfolded position it measures 15 inches wide x 30 inches long and can be placed under or over the mattress. The pad is liquid resistant.

Binocular Clamp

The Binocular Clamp is an extension arm for accessories designed to enable a persons to use a pair of binoculars without having to support the weight of them. The device consists of a 360-degree swiveling clamp fixed to the end of a 13 mm diameter stainless steel rod. The rod mounts onto the fitting of a wheelchair. Binoculars are attached to the device with an off- the-shelf Kaiser binocular fitting. PROTOTYPE DEVELOPMENT: Designed by Colin Knauf for a user with weak arms who can raise the bino

Biosoft Palm Guard Gloves

The Biosoft Palm Guard Gloves are push gloves designed to protect the wearer's hands while propelling a wheelchair. These gloves feature an elastomer palm grip to absorb shock, vibration, and pressure. These pull-on fingerless gloves have an open-weave mesh back with adjustable Velcro closure. SIZES: Small, medium, large, and extra large.

Birdie Buddy

---- PROTOTYPE --------- PURPOSE: To create a prototype of a wheelchair mount for a camera and binoculars for an avid photographer and birdwatcher with quadriplegia. The Birdie Buddy clamps securely to a bar on the wheelchair base frame, holds a camera or binoculars at eye level, and folds down along the side of the wheelchair when not in use. This device supports the weight of the camera or binoculars, convenient switching between the two pieces of equipment, and an adjustable viewing angle. T

Bogen Multi Position Support Arm & Super Clamp

The Bogen Multi-position Support Arm and Super Clamp are mounting hardware for communicators and other accessories designed to be mounted to a table or wheelchair. The Support Arm has a fully articulated arm (three universal joints) with 90 degree pivotable and 360 degree rotatable ends, and an elbow that rotates 360 degrees. The adjustable, one-control handle located at the elbow joints locks all three joints firmly. The arm can be mounted permanently, or used with the Super Clamp. The Super Cl

Bottoms Up Bar

The Bottoms Up Bar is a transfer aid designed for people with lower extremity and mobility disabilities or spinal cord injury and lower extremity amputees. It allows a person in a wheelchair to transfer to a seated position on the ground or floor and from the floor or ground back into the wheelchair. The Bottoms Up Bar attaches to a wheelchair's frame with two collar clamps that are fastened to the front of the frame. The width of the Bottoms Up Bar is adjustable to accommodate multiple wheelcha

Brella Buddy

Brella Buddy is a hands free wheelchair umbrella holder which does not require attachment to a wheelchair. No heavy accessories to carry around when it is not raining. The Brella Buddy, hands free wheelchair umbrella holder will hold your umbrella for you and protect you from the rain while keeping your hands free to propel your wheelchair. The Brella Buddy hands free wheelchair umbrella holder is designed with a two strap, adjustable system to hold it comfortably in place. There are two pockets

Buckles & Belts

Wheelchair seatbelts with 2 types of hook and loop closures, molded plastic Delrin buckle (operates by pinching both sides of buckle simultaneously), lever aircraft buckle, or push button aircraft buckle. Two piece or single continuous belts. Available sizes from 48 to 108 inches.

Cam Belt With Grommets (Model Es-350)

The Cam Belt with Grommets, model ES-350, is a child belt restraint for pelvic stability. The two-piece belt is made of automotive seatbelt nylon and has a nylon buckle. The belt attaches with grommets to various therapeutic equipment and seating aids. The nuts, bolts, and washers required for installation are included. DIMENSIONS (LxW): 40 x 2 inches.

Canadian Padded Transfer Board

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Padded transfer board with a plinth which fits into the forward arm rest socket of a standard wheelchair. Transfer board made of 15 by 6 1/2 inch plywood, a base plate of iron or steel, an iron water pipe, a sheet (10 by 6 inches) of firm leather or plastic, foam padding and a slippery fabric cover. The board is used in place of either arm of the wheelchair. Includes instructions and diagrams. SKILLS REQUIRED: Woodworking. Upholstering. AUTHOR: Wightwi

Carbon Core Wx 2.5

Carbon Core WX 2.5 is a lightweight wheelchair wheel option. It is designed to reduce linear momentum and reduce rotational inertia. The thermoplastic resin and Kevlar/carbon fibers work together to dampen road vibration. The wheelchair spokes are designed to maintain lateral stiffness and firm responsiveness, these composite spokes absorb some of the road "buzz", for greater comfort and control. There is a special thermoplastic carbon fiber composite material for the hub shell. It has strength

Carebike

The Carebike is a cycle attachment for wheelchairs. The unit comprises an anodized aluminum platform on wheels that attaches to a 21-speed comfort bike. It is designed to offer friends, family members and caregivers the convenience of taking a bike ride while still being close at hand to assist the wheelchair user. The wheelchair fits on the platform with the Carebike attached at the rear, giving the biker complete steering, stopping, and starting control.

Casbar, The

The Casbar is a wheelchair push handle extension designed to enable a companion or caregiver to push a wheelchair using one hand. The ends of this C-shaped coated steel bar fit over the existing wheelchair push handles and lock in place using two large adjusting knobs to create a single stroller-style handle. On flat surfaces, this device enables the chair to be pushed and controlled with one hand and on inclines and ramps, using two hands makes pushing less difficult than when using the standar

Challenge Platform Wheelchair Rocker

The Challenge Platform Wheelchair Rocker is a rocking attachment for a wheelchair designed for use by individuals with mobility disabilities or spinal cord injury. This device enables individuals to experience the benefits of rocking without transferring from a wheelchair and is designed for individuals with good upper-body strength and a sense of balance. The platform base has minimal arc, requiring users to exert more force to cause rocking movement.Features include entry/exit from the platfor

Composite Caster

The Composite Caster is a caster wheel designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This lightweight composite unit has a smooth finish that promotes easier turning, reduces rolling resistance, and has no tread to collect dirt . DIMENSIONS (Diameter x Width): 4 x 1.25 inches; 5 x 1 or 1.5 inches; 6 x 1 or 1.5 inches; 8 x 1 inches.

Cursum Stroller

---- PROTOTYPE --------- PURPOSE: To design a prototype of a stroller adapted for a wheelchair to be used by individuals with lower extremity and mobility disabilities, spinal cord injury, and others who use wheelchairs. The Cursum stroller, a wheelchair adaptive stroller, is designed to be used in tandem with a wheelchair. It connects to the front of a wheelchair. Swivel wheels, complete height adjustment, attention to comfort and visibility, and advanced safety features give parents with disab

Curved Transfer Board

The Curved Transfer Board is a transfer board designed for use by individuals who use wheelchairs. Made of solid, reinforced, waterproof plastic that resists chipping, shattering, and splintering, this board has tapered ends and a smooth surface for easy sliding. The curved design accommodates a variety of transfer situations, and slip-resistant pads on the underside at each end increase stability. DIMENSIONS: 27 5/8 inches long and 14 5/8 inches wide tapering to 10 1/8 inches wide in the middle

Cycl-One 3, 12, 48

The Cycl-One is a cycle attachment for manual wheelchairs designed to transform the chair into a hand-propelled cycle. The attachment consists of a front wheel, handcrank shaft, and attachments for mounting onto the wheelchair frame. FRAME: The frame is made of high tensile steel tubing and the crankset is alloy with a 28-tooth chainring (3 and 12 speed models) and 34 tooth chainring on the 48-speed model. HANDLES: The "together"-style hand pedals with parallel horizontal handgrips are designed

Daessy Desktop Mount (Model Ddm-1)

The Daessy Desktop Mount, model DDM-1, is a mounting clamp designed to hold a communication device for individuals who have physical disabilities and use a communication device. The desktop mount provides a stable, hands-free support for any flat surface. It is ideal for individuals who have limited upper limb mobility. The stand comes with the Quick Release Mount, which holds the device firmly yet allows you to remove it with just a flip of a lever.

Daessy Folding Mount

The Daessy Folding Mount is a wheelchair mounting system for communication devices. The unit provides a solid, stable platform that can be adjusted to meet the positioning needs of each individual. The communication device and platform can be rotated down and out of the way beside the wheelchair to permit close-in positioning to a desk or table. Models are available for 7/8-inch tubing, .75-inch tubing, and 1-inch tubing, all in a choice of 6- and 12-inch offset.

Daessy Mini Adjustable Mount (Model M75-Am)

The DAESSY Mini Adjustable Mount, model M75-AM, is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system has several points of adjustment to set up and position the mount. Two rotating joints can be angled and twisted in various directions to adjust the horizontal tube position. The system is supported on the wheelchair by a

Daessy Mini Bent-Tube Mount (Model M75-Btm)

The DAESSY Mini Bent-Tube Mount, model M75-BTM, is a stand for a tablet computer, switch mounting hardware and a computer and communicator mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The mount is non-directional and can be installed on either side of the wheelchair. This product also can be removed from the wheelchair when not needed. The frame clamp assembly includes a

Daessy Mini Folding Mount (Model M75-Fm)

The DAESSY Mini Folding Mount, model M75-FM, is a stand for a tablet computer, switch mounting hardware and a computer and communicator mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The mount is non-directional and can be installed on either side of the wheelchair. The system folds the horizontal tube down to the outside. The folding joint between the two mount tubes brin

Dane Wheelchair Mover

The WheelChair Mover uses a simple hand lever design that activates secure hitching to the frame of the wheelchair. The ergonomic design of the machine allows the user to control the speed with easy and controlled throttle acceleration. With the unit securing the frame at a low center of gravity, turning the wheelchair in a circle is smooth and effortless. Compact and quiet, the Dane WheelChair Mover is the ideal device to fit within hospital rooms and halls while meeting the objectives of safe

Deluxe Transfer Board (Models Nc94205 & Nc94205-B)

The Deluxe Transfer Board, models NC94205 and NC94205-B, is designed to assist people who use wheelchairs. The Deluxe Transfer Board (NC94205) is made from 0.5-inch thick birch and tapers at both ends for transfers. The Bariatric Transfer Board (NC94205-B) features two hand holes and a heavy duty 9 ply birch wood base with 3 additonal piles form-laminate on top. CAPACITY: 450 pounds for NC94205 and 650 pounds for NC94205-B. DIMENSIONS (WxL): 8 x 24 inches for NC94205 and 10 x 32 inches for NC942

Deluxe Wood Transfer Board

The Deluxe Wood Transfer Board is designed for use in transfers to and from wheelchairs. This solid hardwood board has tapered ends and is urethane coated, sealed, and polished for smoothness. The board has a cut-out handle for gripping and carrying. DIMENSIONS (LxW): 30 x 8 inches. CAPACITY: 250 pounds.

Detachable Laptray With Electronic Talking Communicator.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Laptray to securely hold electronic communication device on wheelchair lapboard. A hinged vacuum formed plastic housing was designed to clamp to the desk arms of a wheelchair. By lifting the laptray the individual has immediate access to the communicator, yet it is concealed when it is not in use. The top of the laptray provides a working surface for the individual. Includes photographs. SKILLS REQUIRED: Plastics, woodworking. AUTHOR: David Law, Jr., W

Device To Attach Pram (Child's Stroller) To Wheelchair

CUSTOM ADAPTATION PURPOSE: To design and build a removable device which would lock a pram (child's stroller) into position at the front of a wheelchair for a person with paraplegia. Several ideas were considered but the final solution involved lifting the back wheels of the pram off the ground and putting the weight on the front pram castors and the front wheelchair castors. Lightweight 16-millimeter square steel tubing was used to build a frame which clamps in place on both wheelchair and pram

Direct Mount Clamp (Model 247-Dm100)

The Direct Mount Clamp, model 247-DM100, is lapboard mounting hardware designed specifically for attaching the MYDESC desktop lapboards (see separate entries) to wheelchairs without armrests or without removable armrests. This metal clamp block has a tightening knob for use with tube framing from 0.75 to 1.25 inches in diameter. The device can be mounted either vertically or horizontally, and also features an 0.83-inch cylinder slot to mount the lapboard, or umbrellas, directly onto the wheelcha

Disposable Wheelchair Cover (Model Mc-5)

The Disposable Wheelchair Cover, model MC-5, is designed to protect manual and power wheelchairs, commodes, oxygen tanks, etc. DIMENSIONS: 28 x 22 x 35 inches. COLOR: Clear plastic.

Duet, The

The Duet is a wheelchair tandem cycle designed to provide recreational transportation for two: a wheelchair user or rider with partial or severe physical disabilities, cognitive or visual disabilities, or a pediatric or geriatric passenger, and a non-disabled cyclist. The engineering of the cycle allows passengers from 20 to 275 pounds to fit comfortably by simple adjustments or by using a combination of matching upholstery accessories, seat cushions, and supports. Larger passengers are as easy

Easy Platform Wheelchair Rocker

The Easy Platform Wheelchair Rocker is a rocking attachment for a wheelchair designed for use by individuals who use wheelchairs. This device enables the user to experience the benefits of rocking without transfering from a wheelchair. The rocker features entry/exit using a rear ramp. The adjustable front caster stops center the wheelchair on the platform and two safety straps secure the wheelchair to the platform for added security. DIMENSIONS (LxW): 48 x 30 inches.

Econoglide Transfer Boards

The Econoglide Series are Transfer boards designed to assist people with physcial disabilities in transferring from one surface to another. The boards are fabricated high density stress-relieved linear plastic. The moisture-proof boards are striate-sanded on one side and buff-sanded on the other. Models include the plain board, board with telescope and hand hole, board with hand hole, board with 2 hand holes, board with hand hole and notches, and board with 2 hand holes and notches. CAPACITY: 40

Economy Wheelchair Belt (Model Mdt829110C)

The Economy Wheelchair Belt, model MDT829110C, is a wheelchair seatbelt designed for use by individuals with mobility disabilities or spinal cord injury. This seatbelt restraint helps the wheelchair user to remain upright in the chair without sliding. This belt encircles the user and crosses in back. The belt is made of washable nylon and is latex-free. SIZES: One size fits all.

Econoslide Series Transfer Boards

Econoslide Series Transfer Boards are designed to assist people who use wheelchairs. The 20 models of these boards are made from defect-free 7-ply birch plywood and have rounded corners, ends, and edges. The surface is machine-sanded and finished with clear lacquer. Models include the plain board, board with hand hole and telescope, board with hand hole, board with hand hole and notches, board with 2 hand holes, and board with 2 hand holes and notches. CAPACITY: 400 pounds. DIMENSIONS: All model

Equalizer Shooting System With Custom Chair Mount

The Equalizer Shooting System with Custom Chair Mount is a firearm support for wheelchair and a trigger adapter designed for use by people who use a wheelchair and have limited upper body movement. This system makes it possible for people with physical or neurological disabilities to hunt and shoot from their own wheelchair. The system has over 60 precision machined parts for durability and shooting accuracy, and each chair mount is custom adapted to the user's wheelchair. Multiple brackets can

ERGOtrans Safe Transfer Harness

ERGOtrans Safe Transfer Harness is designed for use with individuals with limited mobility as a result of generalized weakness, stroke, cerebral palsy and Parkinson’s disease.  The Safe Transfer Harness simplifies the safe transfer of individuals between wheelchairs, beds, and automobile.   ERGOtrans can be used for one, two or three person transfers, and helps eliminate dislocated arms, broken ribs, and drops that are endemic to wheelchair transfers. ERGOtrans works great with slide boards and

Essential Hardwood Transfer Board (Model P2300)

The Essential Hardwood Transfer Board, model P2300, is a transfer board designed for use by individuals with mobility disabilities or spinal cord injury. This hardwood board is sealed and highly polished for ease in sliding and features a tapered end and one hand cut-out. DIMENSIONS (WxL): 8 x 30 inches. CAPACITY: 250 pounds.

Essential Plastic Transfer Board (Model P2301)

The Essential Plastic Transfer Board, model P2301, is a transfer board designed for use by individuals with mobility disabilities or spinal cord injury. This high-impact plastic board has a smooth surface for ease in sliding and features a tapered end. DIMENSIONS (WxL): 8 x 27.5 inches. CAPACITY: 250 pounds.

Evoflex Pelvic Stabilizer

The Evoflex Pelvic Stabilizer is a wheelchair seat belt designed for use by individuals with lower extremity or mobility disabilities, spinal cord injury and others who use wheelchairs. The Evoflex has two parts that attach to opposing sides of a wheelchair's seat. When the user is seated in the wheelchair, the two parts attach using a push button seatbelt fastener or a Rehab Latch (available only for the medium and large sizes) to secure the user in the seat. The Evoflex's parts are semi-rigid

Extended Handles

The Convaid Extended Handles are wheelchair push handle extensions designed for use by a companion or caregiver when pushing a manual wheelchair. The Extended Handles provide a more ergonomically positioned handle intended to reduce the strain on the back and wrists of tall people. They also can enhance a person's ability to maneuver a wheelchair up and down hills and stairs. The handles fit most standard, transit, and planar models of pediatric wheelchair and strollers. The extensions sold in p

Figure-8 Clamp (Models 32310 & 32310B)

The Figure-8 Clamp is a seating hardware and a mounting clamp for accessories designed for use with wheelchairs. The two-part clamp is used to attach controls, accessories, and other devices to wheelchairs. One side of the clamp accommodates .75-inch tubing and the other side accommodates 7/8 inch tubing. Deep-set cap screws are used to tighten clamp around tubing. Set screws can provide additional mounting stability. COLOR: Model 32310B comes in black. WARRANTY: The manufacturer warrants this p

Flashlight And Attachment (Model Fl-1000)

The Flashlight and Attachment, model FL-1000, is a cane, walker and wheelchair light designed for use by individuals who use walkers, canes, and wheelchairs. The light attaches to any tube product with a diameter of .875 to 1 inch. It comes with a wrist strap and a clip that pivots 360 degrees to change the direction of the light. The light can also be detached from the clip for use as a flashlight. This light can also be used with bicycles and baby strollers. No tools are required for attachmen

Flexi-Fit Wheelchair Gloves

Flexi-Fit Wheelchair cloves are push gloves designed for use by individuals with severe physical disabilities, spinal cord injury, or who have had strokes. Designed for individuals with limited hand function, these gloves open wide for ease in putting them on. Made from quality neoprene, these gloves have a small textured area built into the palm for added grip. SIZES: Small, medium, large, or extra large.

Folding Manual Wheelchair Cover

The Folding Manual Wheelchair Cover is a wheelchair cover designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury or other people who use wheelchairs. Designed for manual wheelchairs, this cover is weather and dust resistant and is made for travel, wheelchair lifts and storage. Features include a Velcro seam with snap buckle; a front elastic band that wraps around the footrest; a rear drawstring cinch (cord lock) that secures the cover bottom to wheels

Folding Safety Flag

The Folding Safety Flag is a safety flag designed for use on manual or powered wheelchairs or scooters. Designed to increase visibility, this penant-shaped flag has a folding shaft that enables the flag to fold below the user's head when entering and exiting vehicles or when not in use. COLOR: The flag is orange.

Frs 3-D Fixed Position Wheelchair Mount

The FRS 3-D Fixed Position Wheelchair Mount is a communicator mounting kit for wheelchair or scooter designed for use by individuals with communication and mobility, neurological or severe physical disabilities. Designed for use with the ComLink communicators (see separate entries), the flexible mount system is available with a variety of frame clamps to allow attachment to most wheelchair or scooter configurations. The ComLink communicator attaches to the mount by sliding the communicator's mou

Frs 3-D Folding Wheelchair Mount

The FRS 3-D Folding Wheelchair Mount is a communicator mounting kit for wheelchair or scooter designed for use by individuals with communication and mobility, neurological or severe physical disabilities. Designed for use with the ComLink communicators (see separate entries), this flexible mount system is available with a variety of frame clamps to allow attachment to most wheelchair or scooter configurations. The ComLink communicator attaches to the mount by sliding the communicator's mount pla

Frs 3-D Swing-Away Wheelchair Mount

The FRS 3-D Swing-Away Wheelchair Mount is a communicator mounting kit for wheelchair or scooter designed for use by individuals with communication and mobility, neurological or severe physical disabilities. Designed for use with the ComLink communicators (see separate entries), this flexible mount system is available with a variety of frame clamps to allow attachment to most wheelchair or scooter configurations. The ComLink communicator attaches to the mount by sliding the communicator's mount

Funbike

Funbike is a handcycle wheelchair attachment designed for use by individuals with mobility disabilities, neurological disabilities, or spinal cord injury. This unit includes a wheel and hand crank which attach to a wheelchair to convert it temporarily into a hand-propelled cycle. The unit can be attached to a fixed frame wheelchair (recommended) or to a folding wheelchair without removable footrests. The frame and most components are made of aluminum. Standard features include a 20-inch diameter

Gel Gloves (Model Vgb500)

Gel Gloves, model VGB500, are push gloves for manual wheelchair users. The gloves have polymer gel inserts in the palms to provide maximum impact absorption from harmful shocks and vibrations. The half-finger gloves are made of drum-dyed leather, terry cloth, and lycra with velcro closures on the backs of the wrists. SIZES: Small, medium, large, extra large, extra extra large. COLOR: Black palms with two-tone blue backs.

Gloves For Life

Gloves for Life are push gloves designed for use by individuals with quadriplegia, paraplegia, or others with limited dexterity. Custom made of suede with rubber palm inserts, these gloves are designed to make wheelchair wheeling less strenuous. The palms of the gloves are applied to the rims of the wheelchair wheels to aid in propelling and braking the chair. Rubber palm pads prevent heat and friction, helping protect the skin of the palms. A D-Ring is attached to a hook-n-loop strap for a secu

Greenmont's Easypushbar

Greenmont’s easyPUSHBAR is a wheelchair push handle extension designed for use by a companion or caregiver when pushing a manual wheelchair. This stabilizing push bar spans the push handles of a wheelchair to make pushing easier for very tall people or people with lower back pain. Its ergonomic design allows for one-hand maneuvering and comfortable hand positioning. When using both hands, the push bar transfers power directly to the chair with less effort when navigating steep ramps, inclines,

Ground Fx! Lighting Kit

The Ground FX! Lighting Kit is a wheelchair light designed for decorative illumination of a wheelchair. The kit provides colored light under the wheelchair, with fun lighting effects that make the chair glow in a chosen color. The Kit contains 3 IllumiRay Mini lights. Each light has a 12-element circular LED array that emits a brilliant 35 degree cone of light with an output is 8200 MFC. The emitted beam helps the user to operate a wheelchair safely at night. Each light has an anodized aluminum

H-18 Magic Arm

The H-18 Magic Arm is a mounting kit for tablet computers, communicators, or ebooks, an adjustable ebook holder and a stand for a tablet computer designed for use by people with grasping, neurological or upper extremity disabilities, cerebral palsy or arthritis. The H-18 includes the Super-Clamp which allows clamping to wheelchairs, bedrails, desks or tables; and an iPad tablet holder without case or an adjustable tablet holder (ATH) for other devices or tablets such as the Auggie or Super-Auggi

H-57 Mini-Arm For All Ipads

The H-57 Mini-Arm is a stand for tablet computer designed for use by individuals with use of one hand, grasping or upper extremity disabilities, or arthritis. The H-57 is designed for use with the Apple iPad and other tablets. It includes the Super-Clamp (which allows clamping to wheelchairs, bedrails, desks or tables) and an iPad tablet holder without a case or an adjustable tablet holder (ATH). The user can select a standard, tall, or tall and wide ATH. The tablet can be removed from the holde

H-80 Short Arm

The H-80 Short Arm is stand for tablet computer and an adjustable ebook holder designed for use by people with grasping, neurological or upper extremity disabilities, cerebral palsy or arthritis. The H-80 includes the Super-Clamp (which allows clamping to wheelchairs, bedrails, desks or tables) and an iPad tablet holder without case or an adjustable tablet holder (ATH) for other devices/tablets such as Auggie/Super-Auggie (see separate entries), Barnes and Noble Nook, and Amazon Kindle. The user

H-92 Phone Holder

The H-92 Phone Holder is a cell phone holder and tablet computer mounting system designed for use by individuals with upper or lower extremity, grasping and mobility disabilities, individuals with use of one hand, and wheelchair users. The Phone Holder’s gel case attaches to the “Quick Connect” lever which screws into the end of a Short, Mini, Articulating, Magic Arm or Super Clamp (see separate entries). The screw size is 1/4-20. The Phone Holder expands from 1.625 to 4.5 inches. The “Quick-Con

Handicap Placeard Hanger

The Handicap Placard Hanger is designed to fasten safely and securely to the rear-view mirror. It is designed to eliminate stretching and twisting of the back and neck muscles to hang the handicap tag. The "J hook" easily slides around the rear view mirror attachment arm. The Placard Hanger is designed to stay cool even in scorching hot interiors in the middle of the summer. It can be installed on any vehicle.

Hands Free Umbrella Holder

The Brella Bag Hands Free Umbrella Holder is designed for one-handed individuals, those confined to a wheelchair, or for those with upper extremity disabilities who have trouble holding an umbrella to keep them dry while in a wheelchair or in the garden. Lightweight. Deep pouch to hold either a straight or curved umbrella shaft. Features an adjustable strap that wraps around the neck and shoulder. The back strap has a belt loop used to hold the bag more securely. It also features a convenient sn

Haseltine Flyer (Model 504-C)

The Haseltine Flyer, model 504-C, is a wheelchair carrier designed to protect powered wheelchairs during airline travel. The two-piece carrier shell is rotationally molded of recyclable polyethylene and lined with foam padding. The chair is secured to the base piece which has a lip around it to prevent slipping during transit. An internal strapping system holds the chair and its accessories in place. The second piece of the carrier covers the chair and is fastened to the base. The carrier also f

Haseltine Roosevelt Flyer (Model 504-A)

The Haseltine Roosevelt Flyer, model 504-A, is a wheelchair carrier designed to protect folding manual wheelchairs during airline travel. The carrier shell is rotationally molded of recyclable polyethylene and lined with foam padding. An internal strapping system holds the chair and its accessories in place. The container is held closed by six Velcro straps threaded through a footman holder. An additional footman's loop can accommodate an airline luggage tag. The carrier also features an in-mold

Hatch Gloves

Hatch Gloves are push gloves designed for use by individuals who use wheelchairs. These gloves have genuine leather palms and cotton crocheted mesh backs, with half thumbs and fingers. SIZES: Extra-small, small, medium, large, extra-large, and extra- extra-large. COLORS: Tan or black.

Hi D Transfer Board (Model Bk6111)

The Hi D Transfer Board, model BK611, is a transfer board designed for use by individuals with mobility disabilities. Made of polyethylene plastic, this transfer board features a smooth easy slide surface with round corners and centered hand slot. DIMENSIONS (LxWxD): 26 x 10 x .5 inches. WEIGHT: 6 pounds.

Hip Belt

Black nylon webbing belt, padded or nonpadded. 72 inches long by 1, 1 1/ 2, or 2 inches wide. Side release, pushbutton, or lever release buckles. Mounting bands to fit 7/8 or 1 inch tubing available.

Hip Belts (Model Ee 3C/103-5000)

Wheelchair seat belt. Nylin webbing and plastic delrin buckle. Has a pair of iliac crest relief pads so that the belt may be cinched tightly without causing pressure on the bony prominences. Should be mounted at a 45í angle to the seat.

Hip Strap

Velcro strap with mounting hardware and D-ring or buckle closure. Mounts to back of solid back or underside of solid seat.

Hubscrub (Model 20 / 30)

The HUBSCRUB, model 20/30 is wheelchair cleaning system designed to clean, sanitize, and disinfect wheelchairs and other durable medical equipment. The system is housed in an aluminum cabinet with a door on the front. Within the cabinet are recessed, moving nozzles that spray hot (110 degrees Fahrenheit) water provided by a 1 horsepower wash pump. Water drains into a stainless steel internal sink from which water is pumped out by a .33 horsepower drain pump through a raised drain line two to thr

Hubscrub (Model 20 / 50)

The HUBSCRUB, model 20/50, is wheelchair cleaning system designed to clean, sanitize, and disinfect wheelchairs and other durable medical equipment. The system is housed in an aluminum cabinet with a door on the front. Within the cabinet are recessed, moving nozzles that spray hot (110 degrees Fahrenheit) water provided by a 1 horsepower wash pump. Water drains into a stainless steel internal sink from which water is pumped out by a .33 horsepower drain pump through a raised drain line two to th

Iadapter Device Adapter

This device adapter is meant to attach iPads or other tablet devices to wheelchairs. It is meant to work with the RJ Cooper & Associates' Magic Arm, Articulating Arm and Mini-Arm. The adapter attaches to the back of the iPad or tablet with heavy-duty Velcro.

Illumiray Lighting System

The IllumiRay Lighting System is a wheelchair light designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury and others who use a manual wheelchair. The system includes 2 white Solid State Mini Lights, 2 red Solid State Mini Lights, a Black Jack switch and a wiring harness. Each light has a 12-element circular LED array that emits a brilliant 35 degree cone of light with an output is 8200 MFC. The emitted beam helps the user to operate a wheelchair safe

In Your Face Viewbase

The In Your Face Viewbase is a mounting kit for smartphones and other handheld devices that can be used by individuals with upper extremity or grasping disabilities. The unit consists of a flexible gooseneck with a lower clamp for attaching to a table, wheelchair, plane tray, or other support, and an upper clamp for holding the device. The top clamp is spring-loaded, allowing the smartphone to be inserted and removed. The clamp provides a padded and secure tight grip that fits all iPhone and iPo

Independence Mount With Notebook Plate

The Independence Mount with Notebook Plate is a wheelchair mounting kit for communicators and portable computers. Designed to be mounted on the right or left side of the wheelchair, this unit fits most communicators and portable computers and can be adjusted to hold the device at the right height, position, and angle for comfortable operation. This mount can be easily folded out of the way when not in use.

Independent Wheelchair Assistant (IWA)

---- PROTOTYPE --------- PURPOSE: To design a prototype of an electric power assist unit for a manual wheelchair for individuals with lower extremity or mobility disabilities or spinal cord injury so they can independently access their local communities safely and easily. The Independent Wheelchair Assistant (IWA) design utilizes the user’s own wheelchair, acting as a true assistant and eliminating the need to constantly transfer between other devices like scooters or power chairs. The user atta

Ipad Mount

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a customized iPad mount for an electric wheelchair for individuals with mobility disabilities and spinal cord injuries, including people with quadriplegia. A quadriplegic used a computer to organize his activities such as painting, filmmaking, counseling, and motivational speaking. Laptops do not easily mount onto the electric wheelchair, and when the iPad became available, this individual jumped at the chance. Working with TADNSW an iPad b

Ipad Mounting System (Model 1556)

The iPad Mounting System, model 1556, is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system is composed of three parts: a mounting platform for the iPad, a mounting arm, and a clamp. Two flexible cords that securely hold the iPad to the platform are included. The light duty mounting arm expands from 14.5 inches to 24 inch

Iv (Intravenous) Rod And Holder (Model 95)

The IV (Intravenous) Rod and Holder is designed for use with most wheelchairs. This device mounts to a wheelchair back and extends up to hold IV bottles. DIMENSIONS: The maximum extension height is 30 inches.

Kool-Brella

Umbrella, nylon taffeta. Waterproof. Sun reflective due to aluminum-based top-side coating. This automatic opening umbrella has a wooden shaft and handle with a double canopy and Velcro closure straps on both canopies. DIMENSIONS: 48 inch arc. WEIGHT: Less than 2 pounds.

Lap King Wheelchair Lap Desk

The Lap King Wheelchair Lap Desk is a wheelchair lap tray designed for use by wheelchair users. The Lap King is constructed of a two-sided detachable lap tray made of ABS plastic that is attached to a U-shaped microbead fill cushion. The lap tray is reversible with one side having a flat surface on which the user can write, read or eat; and the other side has a dimpled surface that allows the heat generated by a laptop computer to disperse and the computer to remain cool. Both sides of the lap

Large And Tall Power Wheelchair Cover

The Large and Tall Power Wheelchair Cover is a wheelchair cover designed for use by tall individuals who use power wheelchairs. This waterproof cover is designed to fit wheelchairs with high seat backs, and it can fit small and medium chairs. It is available in light weight or heavy duty material. DIMENSIONS (HxLxW): 48 x 44 x 23 inches. The circumference is 124 inches. COLOR: Black

Lifestyle Transfer Board (Models Rtl6044 & Rtl6045)

The Lifestyle Transfer Board, models RTL6044 and RTL6045, is a transfer board designed for use by individuals with balance, lower extremity or mobility disabilities or spinal cord injury. Intended for use in transfers to and from wheelchairs, this board features two horizontal cut-out handles for gripping and carrying. It has rounded corners with tapered ends. The board is made of Baltic birch with a clear lacquer finish. DIMENSIONS: Available in lengths of 24 and 30 inches. CAPACITY: 250 pounds

Lightweight Plastic Transfer Board

The Lightweight Plastic Transfer Board is designed to aid individuals who use wheelchairs in transferring to and from the wheelchair. Molded of high-impact plastic with reinforcement ribs for maximum stength, this board provides a rigid transfer surface between any two level surfaces. DIMENSIONS (WxL): 8 x 30 inches. CAPACITY: 220 pounds.

Lite Transfer Board (Model Bk6466)

The Lite Transfer Board, model 6466, is a transfer board designed for use by individuals with mobility disabilities or spinal cord injury. Made of birch plywood with a lacquer finish, this board has tapered ends and rounded edges for easy sliding. DIMENSIONS (LxWxD): 24 x 8 x .05 inches. WEIGHT: 37 ounces.

Machine Washable Sheepskin Wheelchair Pad

The Machine Washable Sheepskin Wheelchair Pad is a decubitus pad designed for use by individuals at risk for pressure sores. Designed to cover the entire wheelchair (seat and back), it is made of dense pile to reduce pressure on pressure points. Elastic straps hold the Seat Pad firmly in place. DIMENSIONS: 18 X 36 inches.

Magic Arm

The Magic Arm is a mounting attachment for wheelchairs for positioning cameras, joysticks, or other adaptive equipment. This flexible arm has three joints, a 90 degree pivoting end, a 360 degree rotating end, and a 360 degree rotating elbow. Both ends have studs that are tapped and fit any standard 5/8 inch socket. Includes a flash shoe and a camera mounting bracket. This device is designed for use with the Beneficial Designs Super Clamp (see separate entry). DIMENSIONS: Extended length is 19.7

Mesh-Back Wheelchair Glove Series (Model Br607)

The Mesh-back Wheelchair Glove Series, model BR607, by Hatch are a line of all-purpose push gloves for manual wheelchair users. The gloves have half sleeves for the fingers and thumbs, and are made of leather with crocheted mesh backs. A velcro closure is featured on the backs of the wrists. COLOR: Available in 8 assorted colors.

Micro-Tech Seat Belt Alarm

The Micro-Tech Seat Belt Alarm is a wheelchair seat belt and wandering patient system designed for use by individuals who use wheelchairs and have Alzheimer's disease or other cognitive disabilities and are at risk for falls in homes or hospitals. This seat belt is equipped with a standard sensor unit and a Velcro fastening buckle that, once disengaged, alerts a caregiver or hospital staff that the user is exiting the wheelchair and may wander or fall. The Seat Belt Alarm is intended for use wit

Miller's Mounting Hardware Components

The Miller's Mounting Hardware Components are designed for affixing wheelchair accessories to solid seat and back panels or to 7/8 and 1 inch wheelchair frame tubing. Fixed, swingaway, and adjustable type clamps and brackets are available. COLOR: Silver or black chrome finish.

Mjm Transfer Board (Model 600)

The MJM Transfer Board, model 600, is a transfer board designed for use by individuals with mobility disabilities, spinal cord injury, or severe physical disabilities. The board is made of high density polyethylene, and has eight carrying handles and three web nylon restraint straps with side release plastic buckles. DIMENSIONS (LxW): 71 x 23.5 inches. The restraint straps are 2 inches.

Mobilizr

The MOBILIZR is a torso support and wheelchair seatbelt for use by people with lower extremity and mobility disabilities, spinal cord injuries and others who use wheelchairs and need assistance to maintain or regain an upright position. This product requires no tools for installation on a wheelchair or scooter with push handles. It fits around the waist and over one shoulder. The MOBILIZR allows the user to bend forward, and then it aids the user to return to an upright position. It adjusts from

Modularhose.com Assistive Technology Double Kit (Model 90655)

The ModularHose.com Assistive Technology Double Kit, model 90655, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes 6 feet of

Modularhose.com Assistive Technology Double Spring Clamp Kit (Model 90674)

The ModularHose.com Assistive Technology Double Spring Clamp Kit, model 90674, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a 4 x 6 inch plat

Modularhose.com Assistive Technology Kit (Model 90650)

The ModularHose.com Assistive Technology Kit, model 90650, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes 3 feet of Loc-Li

Modularhose.com Assistive Technology Kit Plus (Model 90652)

The ModularHose.com Assistive Technology Kit Plus, model 90652, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes 6 feet of L

Modularhose.com Assistive Technology Kit With Two Plates (Model 90654)

The ModularHose.com Assistive Technology Kit with Two Plates, model 90654, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes preassembled and includes

Modularhose.com Assistive Technology Spring Clamp Kit (Model 90673)

The ModularHose.com Assistive Technology Spring Clamp Kit, model 90673, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a 4 x 6 inch plate, 2 5.75

Modularhose.com At Ipad Kit (Model 90670)

The ModularHose.com AT iPad Kit, model 90670, is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system can be used with iPad 1 and iPad 2. The kit comes with an iPad holder with a silicon edge for protection and grip, an integrated fixed mount plate attached to the iPad holder, 2 spring clamps with integrated fixed mount, 2

Modularhose.com At Starter Kit (Model 90680)

The ModularHose.com AT Starter Kit, model 90680, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit comes with all the common parts used in the assistive tec

Modularhose.com Round Tube Clamp Kit (Model 90750)

The ModularHose.com Round Tube Clamp Kit, model 90750, is a computer or communicator mounting kit for wheelchair or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The kit is intended to be used with Loc-Line 1-inch or 0.88-inch diameter tubing. Plates are made of stainless steel. The kit includes five-piece round tube clamp with knob, Loc-Line connector, Loc-Line double socket f

Modularhose.com Spring Clamp Kit With Plate 1 Foot (Model 90665)

The ModularHose.com Spring Clamp Kit with Plate 1 Foot, model 90665, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a round plate connected to a

Modularhose.com Spring Clamp Kit With Plate 2 Feet (Model 90667)

The ModularHose.com Spring Clamp Kit with Plate 2 Feet, model 90667, is a stand for a tablet computer, a computer or communicator mounting kit for wheelchair, or switch mounting hardware designed for use by individuals with use of only one hand, mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This kit can be used to mount and position a switch, tablet computer, communicator, or a variety of other assistive products. The kit includes a round plate connected to a

Molded Transfer Board (Model 6032)

The Molded Transfer Board, model 6032, is a high-impact, heavy duty plastic board with tapered ends designed to assist individuals with mobility disabilities with transfers. The board is 8.25 x 24.25 inches.

Motorised Wheelchair Mover

CUSTOM ADAPTATION PURPOSE: To enable a recreational therapist who had a back injury to move clients who used wheelchairs around the facility. Because of the back injury, the therapist was unable to push wheelchairs or lift heavy objects. To build the unit, the motor, gearbox, elctronics, and rear wheels of a second-hand scooter were used in conjunction with a chasis built of square hollow section steel. The unit has a platform at the front on which the wheelchair, with its user, is loaded. The

Mount 'n Mover

The Mount 'n Mover is a wheelchair mounting kit for communicators, tablet or laptop computers, or a camera mount for wheelchair designed for use by individuals who use wheelchairs. The device can also be used to mount trays, easels, reading stands, remote controls and more. Available in single- or dual-arm horizontal models, the device is equipped with a quick-release mounting plate offering 0 to 90 degrees of tilt, a paddle to unlock the wrist joint to rotate the attached tray or device, and a

Ne-At Quick Release Mini Trap Assembly

The NE-AT Quick Release Mini Trap Assembly is a a wheelchair mounting bracket that can support an armrest, a drink holder, a tray, or a laptop computer mount. This small, strong quick-release bracket comes in two versions, angle adjustable or not angle adjustable, and it has optional locking pins. DIMENSIONS: 2 x 2 x 0.75 inches.

Neasy Swing Away Aug Com Mounting System

The NEasy Aug Com Swing Away Mounting System is a wheelchair mounting kit for communicators or lapboard mounting hardware designed fo use by individuals who use wheelchairs. This compact, heavy-duty modular mounting system for small to large devices or trays can be released and swung away by the user with only one or two pounds of pressure. Each swing away joint automatically locks into position with a stainless steel, spring-loaded pin at 0 degrees, 90 degrees (optional), and 180 degrees (optio

Norco Push Kuffs (Model Nc94320)

The Norco Push Kuffs, model NC94320, are leather wheelchair push gloves designed to protect the hand from callouses and cuts. The cuffs cover the palm and back of the hands, leaving fingers exposed. The palm features a thick protective pad. The gloves are secured with hook and loop closures.

Orthocare Frame Mounting Block (Model 3042)

The Orthocare Frame Mounting Block ##3042 is a mounting clamp accessory that attaches Orthocare arm supports or positioning orthoses (see separate entries) to wheelchair arms. The block secures to the wheelchair arm with two bolts to grip the tubing, and has two screw holes for orthosis attachment.

Orthocare Sure-Grip (Models 3017 Thru 3022)

Orthocare Sure-Grip gloves are push gloves or dressing mitts designed to allow total hand use while providing complete coverage of the palm, thumb, and back of hand. The gloves are made of polyethylene and rubber with a totally padded, non-slip surface. The gloves have a Velcro cinch strap with D-ring puller. SIZES: Small, Medium, and Large for right or left hand. The gloves can be adapted to a custom fit with ordinary scissors.

Para Gloves (Model Pwc200)

The Para Gloves, model PWC200, by Hatch are push gloves specifically designed for paraplegic wheelchair users. These gloves have three-quarter length finger sleeves and a fully covered thumb sleeve. They are made of leather on the palm side and have a nylon mesh material with Velcro closures on the back side of the hand.

Paraplis Umbrella Holder

The Paraplis Umbrella Holder is an umbrella holder for wheelchair or stroller designed for use by individuals with mobility disabilities or spinal cord injury. The unit attaches to stroller or wheelchair to hold an umbrella to protect both the seated user and an individual pushing the chair or stroller. When in use, it swings up to hold an open umbrella. When not in use, it swings down to carry the closed umbrella at the side of the stroller or chair. The device attaches to any shape bar or tube

Pelvic Stabilization Y Belt (Model 103-4000)

Y belt pelvic stabilization system provides control of pelvic tilt, rotation and obliquity. Price includes modification of solid seat to accommodate (with new seat). Sizes: extra small (6 to 8 inch sitting depth), small (8 to 11 inches), medium(11 to 14 inches).

Pelvic Strap (Sb05)

The Pelvic Strap (model SB05) is a 1 1/2 inch nylon webbing belt designed to position, stablize and restrain an individual's pelvic area wen seated in a seating system or wheelchair. It has a push-button buckle closure. The strap's length is adjustable on one side, and there are three positioning grommets on opposite side.

Personal Tilt Desk

Personal Tilt Desk is designed for use by individuals using a wheelchair and those who need an adjustable desk. The Personal Tilt Desk is adjustable in height and also includes a cut out for additional stability. It is available in mobile or static versions. The Personal Tilt Desk top tilts to provide options for supporting and positioning objects in relation to the child.

Phat Jack

The Phat Jack is a wheelchair lifter designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This unit was designed specifically for the Melrose Rugby wheelchairs (see separate entry), but the manufacturer can customize it for other wheelchairs. To use the Phat Jack, it is rolled under the rear bar of the wheelchair's frame, and the handle is pushed down. The rear of the wheelchair stays up until the handle is lifted back up. The unit lifts and holds

Polar Paws (Model 300)

Polar Paws, model 300, are cold weather gloves designed to ensure the users grip no matter how cold or wet it gets while maintaining hand warmth. Originally designed for use by NFL receivers, these gloves are intended for a wide range of users: Hunters, skiers, ice fishermen, waterskiers and scuba divers to name a few. SIZES: Small-XLarge. WARRANTY: Any products that are found to be defective in material or labor will be replaced at no charge.

Portable Computer Mount

The Portable Computer Mount is a wheelchair mounting kit for communicators and portable computers. Designed to be mounted on the right or left side of the wheelchair, this unit fits most communicators and portable computers and can be adjusted to hold the device at the right height, position, and angle for comfortable operation. This mount can be folded out of the way when not in use, but is not designed to be moved independently by the user.

Posey Body Holder (Model 1731)

The Posey Body Holder, model 1731, is a safety restraint for a bed or wheelchair. It consists of a wide cotton flannel body wrap with four long straps. The restraint's slot may be positioned in the front for limited movement or rear for increased movement of the user. The straps attach to a bed frame or the wheelchair tilt bars with quick-release ties. It is machine washable. SIZES: Small, medium, large and extra large. DIMENSIONS (Pad) (LxW): 41.5 x 7.5 inches (small); 48 x 7.5 inches (medium);

Posey Breezeline Pelvic Holder (Models 4411 & 4427)

The Posey Breezeline Pelvic Holder, models 4411 and 4427, is a pelvic restraint designed for people with lower extremity or mobility disabilities and others who use wheelchairs to prevent the user from sliding out of the wheelchair or geri-chair. It is available with either a double tie strap for triangulation (model 4411) or a slide buckle. SIZES: Small, medium or large. DIMENSIONS (LxW): Model 4411 is 17.75, 21 or 24 x 17 inches (model 4411) or 16.5, 19 or 23 x 17 inches (4427). Upper waist st

Posey Self-Releasing Belt (Models 4183, 4183L, 4220, 4222, 4229 & 5145)

The Posey Self-Releasing Belt, models 4183, 4183L, 4220, 4222, 4229 and 5145, are wheelchair seat belts for people with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs. This belt has an airline-style buckle allowing for one-handed release by the user. It is made of machine-washable polyester webbing and can be used on a shower chair. The belt mounts on the wheelchair or shower chair with a screw (models 4183 and 4183L), rear removable buckle (4220),

Positioning Belt (Buckle Type) (Model 92133040)

The Positioning Belt (Buckle Type), model 92133040, is a wheelchair seat belt designed for use by individuals with mobility and lower extremity disabilities or spinal cord injury. The belt is adjustable and constructed of black nylon webbing with a metal buckle. The seat belt mounts to the wheelchair back at waist level, and it includes attaching hardware. DIMENSIONS (LxW): 36 x 2 inches.

Posturetex-Multiway Cushion

Posturetex-multiway cushion is designed for individuals with limited mobility and use a wheelchair or a scooter for mobility. It is a versatile cushion featuring a 2 inch nodular foam base as well as a 2 inch nodular foam back which can be folded in half to make a 4 inch base cushion. The 2 inch base cushion is available with standard or coccyx cut out. Covered in black jacquard velvet which is removable for machine washing and a carry handle easy transportation. Spare covers are also available

Power Buddy

The Power Buddy is a USB charger for powered wheelchairs and wheelchair light designed for use by individuals with lower extremity, mobility or severe physical disabilities. The unit plugs into the charger port of the wheelchair controller and enables the user to charge cell phones, MP3 players, tablet computers, and other USB devices while in the wheelchair. A universal USB adapter is included. The unit is equipped with a flexible gooseneck to enable positioning to meet the user's needs. The un

Power Chair Cover (Model 0129)

The Power Chair Cover, model 0129, is a wheelchair cover designed for use on powered wheelchairs. Made of weather-resistant nylon, the cover features elasticized, reinforced seams that fit the cover to the powered wheelchair. There are grommets along the bottom edge if the cover needs to be tied down. A cover storage bag is included. DIMENSIONS (HxLxW): 32 x 35 x 23 inches. COLOR: Black. WARRANTY: One-year limited warranty.

Profiler Mounting System

The Profiler Mounting System is a wheelchair mounting kit for communicators. This system mounts to wheelchairs, walkers, hospital beds, strollers, or tables. Lightweight and adjustable, the unit is available for mounting on square or round tubing (specify choice) and can be moved to the side with the lift of a single lever when not in use. This system accommodates most communicators and notebook computers. The unit supports up to 15 pounds. OPTIONS: A variety of mounting plates and release optio

Profiler-Lite Mounting System

The Profiler-Lite Mounting System is a wheelchair mounting kit for communicators or switch mounting hardware. This system mounts to wheelchairs, walkers, hospital beds, strollers, or tables with square, oblong, or round tubing. This system accommodates lightweight communicators and most switches and supports up to five pounds, including pressure on the device. The unit can be mounted on the right or the left side and the universal base mount can be adjusted 360 degrees from front to back and 180

Push & Transfer Glove

Push & Transfer Gloves are push gloves designed for use by manual wheelchair users. The glove has open fingers, a half thumb, and wrap-around design. Padded in palms and wrist, it is made of 100 percent leather with, and it is available with a leather or non-slip rubber grip surface. It has dual Velcro closure with 3 inches of Velcro to allow for a secure fit. COLOR: Black.

Push Ease Full-Finger Gloves

Push Ease Full-Finger Wheelchair Glove are push gloves designed for use to protect the hands of manual wheelchair users. These general purpose wheelchair gloves protect the most vulnerable areas of the hand from blisters and injury while propelling a wheelchair.The gloves have full fingers with gel padding at the most crucial areas of the hand and removal tabs to assist in taking gloves off. Machine washable. SIZES: XX Small, X Small, Small.

Push Ease Half-Finger Wheelchair Gloves

Push Ease Half-Finger Wheelchair Gloves are push gloves designed to protect the wearer's hands while propelling a wheelchair. These gloves have gel-padded palms, partial finger coverage, and removal tabs to assist in taking gloves off. The gloves are machine-washable. SIZES: Small for hands 2 5/8 to 3 1/8 inches wide, medium for hands 3 1/8 to 3 5/8 inches wide, large for hands 3 5/8 to 4 1/8 inches wide, extra large for hands 4 1/8 to 4 5/8 inches wide.

Push Handle Extensions

CUSTOM ADAPTATION PURPOSE: To enable a tall parent to push a child's wheelchair. The existing pish handles were sawed off the chair and new ferrules were fixed inside the exposed tubes with Loc-tite. Two new L-shaped handles were fashioned from metal tubing and one end of each was fitted into the new ferrules. The new handles were painted red to match the rest of the chair and finished with rubber bicycle-style handgrips. TITLE: Bicycle and Beyond. JOURNAL: TAD Journal. REF: Volume 26, Number

Quad Glove (Model Qg01)

The Quad Glove, model QG01, is a push glove designed for use by individuals with spinal cord injury or severe physical disabilities. This wheelchair glove opens up, allowing fingers to slide right in, and folds over the hand, securing with Velcro. Especially designed for wheelchair use, it features drum-dyed leather, soft enough for flexibility, yet strong and durable for tough wear. It extends up to the inside of the wrist to protect this sensitive area and is padded in all critical areas with

Quad Gloves With Rubber Palms

Quad Gloves are push gloves designed for use by individuals who use manual wheelchairs. These fingerless gloves fully open, enabling the fingers to slide in, folds over the hand, and secures with Velcro. The drum-dyed leather gloves are flexible and extend up the inside of the wrist for added protection and are padded with closed-cell foam at critical areas to prevent friction burns and nerve irritation. Technologically advanced rubber is sewn into the palms for gripping and protection. SIZES: E

Quad Push Cuff

Quad Push Cuffs are rubber crepe fingerless gloves with thumb flaps and a Velcro closure. The material covers the heel of the hand and the base of the thumb. SIZES: Universally sized (one size fits all); may be trimmed with scissors.

Quik Mount (Model M1015)

The Quik Mount, model M1015 is a mounting clamp designed for attaching head supports to wheelchairs. This bracket provides a quick and easy way for clinicians to attach head supports to wheelchairs for evaluation purposes. It can also be used on chairs that have sling style back upholstery.

Racing Wheelchair Stabilizer

DO IT YOURSELF ENTRY --- PURPOSE: To facilitate transferring a child to a racing wheelchair. The unit has a plywood base with a pipe frame at the front to hold the front wheel; the front wheel is further secured with a Velcro strap. This stabilizes the racing wheelchair for ease of transfers in and out with one person assisting. The half-inch thick plywood base is made to the size of the wheelchair, and excess material is removed to create a lighter weight base. The pipe frame consists of one-in

Ram Mounts Ez-On/off Flexible Seat Clamp Mount

The RAM Mounts EZ-ON/OFF Flexible Seat Clamp Mount is a stand for a tablet computer, cell phone holder and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. This mount consists of a universal mount with clamp and 2.5-inch diameter ball base, an 18-inch flex rod, a single socking mounting system, and a custom high strength composite non-locking cradle holder for the

Ramp To Tilt Wheelchair To Comfortable Eating Position

CUSTOM ADAPTATION PURPOSE: To enable an individual with cerebral palsy who uses a wheelchair with tilt-in-space seating to eat independently. The user's disability prevents upright sitting, so a low-level ramp was constructed to raise the wheelchair's rear wheels. Seventeen millimeter lightweight plywood was used to construct the sloping portion of the ramp, and five slats of 50 x 25 millimeter wood were used to fashion a gutter to hold the rear wheels in place. The same type of wood was used t

Rehadesign Gel-Palm Wheelchair Gloves

RehaDesign Gel-Palm Wheelchair Gloves are push gloves designed for use by individuals who use wheelchairs. Designed to diminish impact force to the hand, these wheelchair gloves have half fingers and an enclosed thumb and are made from quality soft leather with gel padding built into the palm. They have a terry sweat-wipe backing. SIZES: Small, medium, large, and extra large.

Rehadesign Ultra-Grrrip 4 Seasons Wheelchair Gloves

RehaDesign Ultra-Grrrip 4 Seasons Wheelchair Gloves are push gloves designed for use by individuals who use wheelchairs. Suitable for all-weather use, these full-fingered leather gloves have a textured palm for improved grip. SIZES: Small, medium, large, and extra large.

Reps Wheelchair Gloves (Model Wh-1)

REPS Wheelchair Gloves, model WH-1, are push gloves designed for wear by wheelchair users. These gloves have three-quarter length fingers and thumb and are made of tough suede padding to protect the hand's main contact points with the wheel. The gloves have terrycloth lining on the inside of the palm for additional protection and comfort.

Reps Wheelchair Gloves (Model Wh-2)

REPS Wheelchair Gloves, model WH-2, are push gloves designed for wear by wheelchair users. These gloves have a three-quarter length thumb and no fingers. Made of soft leather with a nylon spandex back, these gloves have tough suede padding to protect the hand's main contact points with the wheel and a terrycloth lining on the inside of the palm for additional protection and comfort. SIZES: Small, medium, large, or extra-large. COLOR: Black.

Reps Wheelchair Gloves (Model Wh-4)

REPS Wheelchair Gloves, model Wh-4, are wheelchair push gloves designed for use by individuals with limited hand mobility. These wrap-around gloves are made of durable suede leather with padding to protect the hand's main contact points with the wheel.

Reps Wheelchair Gloves (Model Wh-5)

The Reps Wheelchair Gloves, model WH-5, are wheelchair push gloves designed for use by individuals who use wheelchairs. These gloves have full-length fingers and thumb and are made of durable suede leather with padding to protect the hand's contact points with the wheel.

Resident-Release Three-Point Wheelchair Belt (Models 610210 & 610215)

The Resident-Release Three-point Wheelchair Belt is a wheelchair seatbelt designed to provide security and positioning assistance. This automotive style-belt is a combination lap and shoulder belt that secures to the wheelchair using the existing screws. Model 610210 has side-release buckle closure and model 610215 has a user-friendly buckle. SIZES: One size fits most.

Rio Mobility Dragonfly Attachable Handcycle

The Dragonfly™ is an attachable handcycle for use by individuals with mobility issues. The Dragonfly attaches to most wheel chairs. Ergonomic hand cranks fit a wide range of riders and facilitates maneuverability for the user. Built-in coaster brake lets users control speed without removing hands from the handle. The secondary brake lever has a parking feature that keeps chair in place.

Rock’n Roller

---- PROTOTYPE --------- PURPOSE: To create a prototype of a motorized sensory platform for a high school student with shaken baby syndrome to allow her to enjoy movement and music independently. The young woman has severe cognitive, visual, and physical disabilities and poor muscle coordination. She can only voluntarily control her head and right hand. She spent most of her time in a manual wheelchair and was unable to propel herself. Her teachers were unable to give her constant 1-on-1 attenti

Rocking Chair Adapter For Wheel Chair

CUSTOM ADAPTATIONPURPOSE: To make it possible for a wheelchair to absorb the shocks from the involuntary backward and forward movements of a girl with cerebral palsy. This girl has broken parts of her chair several times previously. Instead of building a special rocking chair, it was decided to convert the wheelchair itself into a rocking chair. A device was built using 6-millimeter thick aluminium plate rolled to a suitable curve. The chair can be rolled onto the device and tied down. The devic

Rockstar Guitar Stand

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a customized guitar stand that attaches to a wheelchair for an adult male with cerebral palsy. The Rockstar guitar stand provides a safe and durable attachment for the user’s wheelchair which supports his electric guitar and keyboard. The device attaches to the armrest supports of the wheelchair and allows for adjustment of the guitar platform to the most comfortable position for the user. When brainstorming design ideas it was decided that

Rolyan Workhard Open Finger Glove (Models A38257 To A38268)

The Rolyan Workhand Open Finger Glove, models A38257 to A38268 is a glove designed to absorb shocks and vibrations for persons with arthritis or other neurological disabilities. Constructed of leather with Sorbothane lining and a Lycra back side, the washable glove is available for the left or right hand. SIZES:: To determine size, make a loose fist and measure the circumference of the hand just below the knuckles. Extra extra small is up to 7 inches wide; extra small is 7 1/8 to 7.75 inches wid

Safe T Spin For Disabled Awareness (Model Da-50)

The Saf T Spin for Disabled Awareness, model DA-50, is a safety flag designed for use by individuals who use wheelchairs. This warning signal draws attention to wheelchairs by adding height and motion. Atop a fiberglass rod that attaches to a wheelchair, this rotating signal carries the wheelchair disability and can be seen over the rooftops of vehicles while the wheelchair is crossing intersections or parking lots. A fitting in the middle of the fiberglass rod allows for assembly and disassembl

Safe•t Mate Adjustable Front Anti-Tippers (Model Sm-011)

Safe•T Mate Adjustable Front Anti-Tippers, model SM-011, are anti-tipping attachments designed for use on wheelchairs. These anti-tippers have five height adjustments to accommodate wheelchairs from full height chairs to low hemi chairs. The attachment is made from powder- coated steel tubing and heavy-guage chrome- plated steel with easy gliding wheels. Mounting hardware and installation instructions are included. DIMENSIONS: These anti-tippers fit chairs with frame tubing 7/8 or 1 inch in diam

Safe•t Mate Alarmed Velcro Seatbelt (Models Sm-005 & Sm-005L)

The Safe•T Mate Alarmed Velcro Seatbelt is a wheelchair seatbelt and wandering patient alarm designed for use by wheelchair users with Alzheimer's disease or cognitive disabilities. This Velcro lap belt has a alarm that sounds when the belt is separated to alert caregivers and remind the user to remain seated. The nylon belt features a bright red pull strap to facilitate locating and releasing. The alarm box features a heavy duty on/off switch and a stainless steel universal mounting clip. Horn

Safe•t Mate Sm2 Anti-Rollback Device

The Safe-T Mate SM2 Anti-Rollback Device is an anti-tipping attachment designed for use by individuals who use wheelchairs. This device prevents a wheelchair from rolling back by grabbing the tires as the user attempts to sit or stand. The seat pad has three height adjustments for regular, hemi, and extra-low chairs. The articulating/floating pad moves forward to accommodate users who slouch in their chairs while remaining in proper alignment with the seat bottom. This device is compatible with

Safe•t Mate Universal Fit Rear Anti-Tippers (Model Sm-008)

Safe•T Mate Universal Fit Rear Anti-Tippers, model SM-008, are anti-tipping attachments designed for use by individuals who use wheelchairs. These rear anti-tippers have sliding height adjustment allowing them to fit various makes and models of chairs and to be positioned at different heights. These anti-tips are made from solid bar stock with gliding wheels. Their height is infinitely adjustable within a 10-inch range. DIMENSIONS: 2 foot diameter wheels. WARRANTY: Guaranteed for one year from

Safe•t Mate Wheelchair Labeling System (Model Sm-003)

The Wheelchair Labeling System, model SM-003, is a wheelchair labeling system designed for use on wheelchairs used in facilities with multiple wheelchair users. This product allows staff to manage user-specific wheelchair accessories, such as leg rests or lap cushions. Each chair can be outfitted with a flexible plastic bracket that has a vinyl label. Each label contains spaces for the user name, room number, chair accessories and total chair weight. Each unit contains a set of 10 brackets with

Safety Flag

The Safety Flag is a wheelchair safety flag designed for use by individuals who use power wheelchairs. Designed with extended shaft height coupled with the flag’s high-visibility color and logo, this safety flag is intended to increase visibility while using powered wheelchairs in busy areas or areas that are poorly lit. The flag is made of durable vinyl and is easily removed when not in use. DIMENSIONS: The shaft is six feet long. COLOR: The flag is orange.

Safety-Soft Security Belt (Models Mdt822125 & Mdt822126)

The Safety-Soft Security Belt is a wheelchair seatbelt designed for use by individuals with cerebral palsy, mobility or neurological disabilities, or spinal cord injury. This seatbelt helps keep wheelchair users upright. The belt has a polyester strap with a thick foam lining to reduce friction on the user's hips. It has bar tacks at stress points and is washable. The one-piece style (model MDT822125) is a single piece of foam that ties behind the back. The two-piece style (model MDT822126) has

Sammons Preston Hardwood Transfer Board (Models 6113 & 6114)

The Maple Transfer Board models 6113 and 6114 are transfer boards designed for use by people with mobility disabilities. The boards features a highly lacquered finish and tapered ends. DIMENSIONS (DxLxW): Model 6113 is .75 x 24 x 8 inches and model 6114 is .75 x 30 x 8 inches. Both models taper to 1/8 inch at the ends. COLOR: Natural maple.

Sammons Preston Wheelchair Pushing Cuffs (Model 9470 & 9471)

The Sammons Preston Wheelchair Pushing Cuffs, model 9470 and model 9471 are push cuffs designed to protect the palms and provide a better grip while propelling a wheelchair. The finger and thumb areas are open to permit full hand use at all times. The cuffs are secured to the hand with a leather strap and D-ring fasteners. Model 9470 are made of soft suede with non-slip Dycem palms, and model 9471 are made of plain suede. Model 9470 are $28.95 and model 9471 are $65.95. SIZES: One size fits all.

Sammons Preston Wheelchair Pushing Cuffs (Model 9470)

The Sammons Preston Wheelchair Pushing Cuffs, model 9470, are push cuffs designed to protect wheelchair user's hands and provide a better grip and traction while propelling a wheelchair. These suede leather gloves feature open fingers and thumb and a non-slip pad sewn into the palm. They slip on using a leather strap and D-ring closure. SIZES: One size fits all.

Seasucker Ipad Mounting System

The SeaSucker iPad Mounting System is a stand for a tablet computer and a computer mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The system requires no bracket for the iPad; it has a 4.5-inch diameter vacuum mount that attaches to the back of the iPad. This mount attaches to a flexible RAM arm that can be moved to position the iPad as needed. The arm attaches to a second

Seat Belt Kit

The Seat Belt Kit is a wheelchair seatbelt designed for use with the Otto Bock MOSS II seating systems (see separate entries). The kit consists of webbing with a plastic side-release or push button-style buckle. DIMENSIONS: 1.5 and 2 inch widths.

Seat Belts

The Seat Belts are wheelchair seatbelts designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Available styles include auto-style belts and dual-pull belts with comfort pads. OPTIOS: Slide-on and sew-on comfort pads are available. DIMENSIONS: 1.5 or 2 inches wide. Custom lengths are available.

Self-Assisting Belt (Model 4220)

The Self-Assisting Belt, model 4220, is a wheelchair seatbelt designed to reduce siding in wheelchairs. This belt attaches to a wheelchair or geri chair using a slide buckle. Made of heavy-duty nylon, this machine-washable belt is equipped with an airline-style buckle. DIMENSIONS: Fits hips up to 60 inches.

Self-Assisting Belt (Models 4228 & 4228L)

The Self-Assisting Belt is a wheelchair seatbelt designed to reduce sliding in wheelchairs. This belt attaches to a wheelchair or geri chair using a slide buckle. Made of polypropylene webbing, this machine-washable belt is equipped with Velcro closure. DIMENSIONS: Model 4228 fits hips up to 42 inches and model 4228L is extrsa-long to fit hips up to 62 inches.

Sheepskin Seat Belt Cover

The Sheepskin Seat Belt Cover is a wheelchair seat belt accessory designed for use by individuals with spinal cord injury or mobility disabilities. This sleeve fits over the seat belt and secures with Velcro to help reduce pressure and absorb moisture. They DIMENSIONS: 8 inches long. COLOR: Available bone or charcoal grey.

Side By Side

---- PROTOTYPE --------- PURPOSE: Side by Side is an accessory for the wheelchair which allows a friend, relative or caregiver to push the chair while walking beside rather than behind it. Called Side by Side, the prototype device is designed to enable eye contact to encourage conversation. This design keeps the wheelchair from turning on the spot when pushed. The device can also be folded to fit into the rear pocket of the chair.

Sidelyer Strap, H-Straps, & Pelvic Strap

The Sidelyer Strap, H-Strap, and Pelvic Strap are restraint and positioning belts designed for use in conjunction with the large foam positioning shapes by the manufacturer (see separate entries). The straps are fabricated of Evazote foam for cushioning ithout bottoming out. The Sidelyer Strap is designed to support the body in proper alignment when positioned on its side. It comes in Adult and Child models, both available with a hole for a gastrostomy tube. The H-Straps form a harness and are u

Single Switch Remote Controlled Camera

---- PROTOTYPE --------- PURPOSE: To create a prototype of a single switch remotely controlled camera for an individual with cerebral palsy. A young man with cerebral palsy who had no use of his hands wished to independently operate a camera. Mounting the camera to the young man’s wheelchair was straightforward. The remote control cable for his camera required two switch actions, one to focus the camera and the other to simultaneously trigger the shutter. The young man currently used a switch ar

Sitkit

The SitKit is a wheelchair fitting system designed for use by clinicians and suppliers to optimize the fit of a wheelchair for an individual user with mobility or lower extremity disabilities or spinal cord injury and others who use wheelchairs. The SitKit includes a reversible caliper handle for hip width and upper leg measurements; a laser height gauge for lower leg measurement; a digital angle gauge for calculating the proper wheel camber, backrest angle, front frame angle, and foot plate ang

Skil-Care Resident-Release Nylon Belts (Series 7010)

Skil-Care Resident-Release Nylon Belts, series 7010, are wheelchair seatbelts designed to provide security and positioning assistance for people who use wheelchairs. These belts secure to the wheelchair using the existing screws and are available with a choice of four closures: Side-release buckles, user-friendly buckles, Velcro, and Velcro with a red hand loop. DIMENSIONS: All models are two inches wide. The model with the side-release buckle is available in 42 or 54 inches long. The model with

Skil-Care Resident-Release Soft Belts (Series 3012)

Skil-Care Resident-Release Soft Belts series 3012,are wheelchair seatbelts designed to provide security and positioning assistance. These launderable foam padded belts are available with a choice of four closures: Side-release buckles, user-friendly buckles, Velcro, and Velcro with a red hand loop. Foam padded belt easily attaches to wheelchair kick spurs.DIMENSIONS (padded front) (LxW): 24 x 4 inches. Overall length is 81 inches.

Sleeve Guards

The Sleeve Guards are sleeve protectors designed for use by individuals who use manual wheelchairs. These guards are worn over the user’s original garment to protect shirt sleeves, jackets and skin against moisture and dirt from the wheelchair's wheels. SIZE: One size fits all.

Slim Armstrong Mounting System

The Slim Armstrong Mounting System is a mounting system for communication devices or switches that can be attached to wheelchairs, bed frames, tables or trays for activities at home, school, work and in the community. The device has a slender, telescoping arm that holds up to 5 pounds. The system includes the following components: a clamp for anchoring on most curved or flat surfaces, a ball joint, a flexor rod with built-in ball joint, a telescoping arm, and a small triangular mounting plate. T

Slim-Grip Bike Mount With Safety Strap (Model Sm532)

The Slim-Grip Bike Mount with Safety Strap, model SM532, is a cell phone wheelchair mount designed for use by individuals with lower extremity or mobilitiy disabilities or spinal cord injury. Originally designed for bicycles, this low profile mount is compatible with most smartphones with a screen size of 3.2 inches or more, with or without a case, including the iPhone, HTC, Samsung, Motorola, LG, Sony Ericsson, and ASUS. The mount has a 180 degrees tilt-swivel head that allows maximum viewing p

Soft Surface Transfer Board (Models Tb-23Sst & Tb-28Sst)

The Soft Surface Transfer Board is a transfer board designed for use by individuals who use wheelchairs. This board is designed to assist with transfers from a wheelchair to a softer surface such as a bed or lift chair. The pear shape of this board minimizes sinking into a soft surface when transferring, creating a more level transfer. The wide end of the board distributes the users weight over a broader area relulting in a transfer with little or no incline or decline. OPTIONS: Available with o

Super Clamp

The Super Clamp is a mounting clamp for accessories designed to attach to wheelchair arms or any other kind of frame. The jaws of the clamp open up to a maximum of two inches wide. The clamp has a receptacle to screw into photographic or other equipment. The device is made of cast alloy with a high strength to weight ratio. The jaws are friction lined and screw operated. The clamp has a special detent operated safety lock that holds accessories in place even if the locking mechanism is not tight

Support Fixture For Powered Wheelchair

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a support fixture for a powered wheelchair for a woman with a progressive neurological disorder to travel independently away from the hospital with all her required medical pumps and support devices. This young woman is dependent on getting her food and medications through pumps attached to her powered wheelchair by a customized bracket. As her medical needs have increased she needed three additional pumps to meet her needs, but the bulk an

Swinging Backpack

---- PROTOTYPE --------- PURPOSE: A group of seven students from a Wethersfield, CT high school developed the Easy Access Transport System (EATS). The device is designed to solve a problem that a student with Charcot-Marie-Tooth (CMT) disease had accessing his books in his backpack on the back of his wheelchair. Over two months, the EATS was designed to allow the student with CMT to swing his backpack on hinges and bring it around to his lap so he could access his books. The students started wit

Switch Mounting Kit (Models Smt & Smw-1)

The Switch Mounting Kit for Tables, model SMT, and Switch Mounting Kit for Wheelchairs SMW-1, are control switch accessories for mounting switches in a variety of locations. Model SMT is designed for use on tables or table-like surface, and model SMW-1 is designed for use with wheelchairs. The Switch Mounting Kit for Tables includes a gooseneck, tilt-top switch mounts, and an adapter bracket to fasten it to tables or shelves. The Switch Mounting Kit for Wheelchairs has a tubular bracket for clam

Takeoff Sport And Wheelchair Gloves

TakeOff Sport and Wheelchair Gloves are push gloves designed for use by individuals who use wheelchairs. Made from Amaretta synthetic leather, these half-fingered gloves are lined with gel througout the palm and all five digits.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra-small, small, medium, large, and extra-large. COLOR: Black with blue backs.

Takeoff Sport And Wheelchair Gloves-- Full Finger

TakeOff Sport and Wheelchair Gloves--Full Finger are push gloves designed for use by individuals who use wheelchairs. These full-fingered gloves are lined with gel througout the palm and all five digits.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra-small, small, medium, large, and extra-large. COLOR: Black with blue backs.

Takeoff Sport And Wheelchair Gloves-- Half Finger, Full Thumb

TakeOff Sport and Wheelchair Gloves--Half Finger, Full Thumb are push gloves designed for use by individuals who use wheelchairs. These half-fingered, full thumb gloves are lined with gel througout the palm and all five digits, and the thumb and palm are reinforced with rubber material for improved grip.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra

Takeoff Sport And Wheelchair Gloves--Half Finger

TakeOff Sport and Wheelchair Gloves--Half Finger are push gloves designed for use by individuals who use wheelchairs. Made from cabretta leather, these half-fingered gloves are lined with gel througout the palm and all five digits.These gloves also feature a reinforced leather web space, double stitching on the palms, seamless forefingers, terry cloth nylon/Lycra backs, and TakeOff tabs for easy glove removal. SIZES: Extra-small, small, medium, large, and extra-large. COLOR: Black with blue back

The Communication Station

The Communication Station is a wheelchair mounting kit for communicators designed to clamp an augmentative device to a wheelchair for individuals who are non-verbal and use a wheelchair. It is designed to "lock in" communciation devices at the right height, position and angle. The monoclamp is the key to the Communciation Station and can be configured in various combinations with almost limitless possibilities. The family of mounts can adapt any device to the left or right side of any wheelchair

Theraslide Transfer Boards

Theraslide Transfer Boards are designed to assist people who use wheelchairs. The 20 models of these boards are constructed from defect-free birch plywood and machined from 7-ply base board with 3 additional plies form-laminated over this surface from end to end, producing a smooth, uninterrupted surface. All edges are computer routed and the surface is machine- and hand-sanded and finished with multiple coats of semi-gloss lacquer/sealer. Models include the plain board, board with telescope and

Thomashilfen Quick Base (Q-Chassis) High-Low Base

Thomashilfen Quick Base (Q-Chassis) High-Low Base is an alternative frame designed for use by children with neurological and mobility disabilities. It that allows you to move the Thomashilfen seating systems from the mobility or stroller base, creating an indoor base that is great for family, therapy, or classroom inclusion. The Thomashilfen Quick Base is equipped with a patented tipping prevention function called the Balance Safety System or BSS. When the back of EASyS is reclined, the seat

Three-Dimensional Aid For Teaching Wheelchair Maintenance.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Visual aid showing the interior and exterior components of a wheelchair. Developed as a training tool in wheelchair maintenance. Describes training tool designed to allow persons with little mechanical experience to see how wheelchair components interrelate. One side represents an exterior view of an intact wheelchair, the other depicts unassembled interior components (i.e., bearings, axles and front post guides). Lists material needed and describes co

Tilt'n Turner

The Tilt 'n Turner is a communicator or computer mounting kit for wheelchair or a camera mount for wheelchair designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. The device can also be used to mount trays, easels, reading stands, remote controls and more. The device is equipped with a quick-release mounting plate offering 0 to 90 degrees of tilt and a paddle to unlock the joint to rotate the attached tray or device 360 degrees. There are 12 memor

Tms Padded Chair Belt

Padded belt support. Two 12 inch long canvas pads with webbing strap sewn at one end. Straps attach under wheelchair upholstery screws and canvas pads fit across abdomen. Velcro closure.

Tms Padded Chair Belt

Belt for wheelchair, webbing straps for attachement to chair, Wide padded canvas body strap, two rows of velcro for closure.

To Narrow Your Chair.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Describes method to temporarily narrow a wheelchair. Suggests pulling the front or rear posts of the wheelchair together with a strong leather belt or a straightened coat hanger. AUTHOR: Lunt, S TITLE: Handbook for the Disabled: Ideas and Inventions for Easier Living REF: New York: Charles Scribner's Sons: p 212 NARIC CALL NUMBER: R1616 PAGES (including cover): 2 1982.

Transfer Board (Model 765)

The Transfer Board, model 765, is designed to aid a person with lower extremity or mobility disabilities or spinal cord injury to transfer from a wheelchair or chair to a commode or bed and back. It has gradually tapered ends and is constructed of hardwood and has a smooth, natural finish. DIMENSIONS (WxLxT): 8 x 30 x 0.75 inches.

Transfer Board (Model 765H)

The Transfer Board, model 765H, is designed to aid a person with lower extremity or mobility disabilities or spinal cord injury to transfer from a wheelchair or chair to a commode or bed and back. It features hand slots with tapered ends, and it is constructed of 14 ply hardwood with a smooth, natural finish. DIMENSIONS (WxLxD): 8 x 30 x 0.75 inches; hand slots 19 inches apart.

Transfer Boards

Transfer board made of solid red oak electronically glued for strength and crack resistance. Finished boards are coated with urethane sealer and polished. Unfinished boards are sanded smooth and are ready to finish. Boards are 8 inches wide, available without hand hole, with one hand hole or with 2 hand holes, and in 24 or 30 inch lengths.

Uclamp Bundle (Wheelchair Umbrella Attachment Device)

The uClamp Bundle is a mounting clamp for wheelchair accessories designed for use by wheelchair users. The height-adjustable uClamp and extension pole enables the wheelchair user to have an umbrella attached to the clamp which, in turn, is fixed to either the frame of the arm or back section of a wheelchair or mobility vehicle. Each uClamp set comprises two clamps that work independently of each other. Both clamps are held together by a spindle and two tightening knobs, one at each end. Each ti

Ucosy Weathershield

The uCosy Weathershield is an umbrella for wheelchairs and strollers designed to protect a caregiver up to 6 feet, 4 inches tall pushing the mobility aid. The uCosy comprises a collapsible canopy made from durable nylon connected to telescoping poles fitted with uClamps (see also separate entry) capable of 360-degree rotation. Twin rotating uClamps attach simultaneously to the canopy poles and the structure of the wheelchair or stroller with the rotation controlled by simple turn-wheels. These c

Ultraslick Transfer Board

Transfer board to aid in transferring from wheelchair to bed or chair or toilet. Fiberglass laminated with hardwood. Lengths: 18, 24, or 30 inches. Available with or without hand holes on each end.

Universal Arm Mount (Model 347-Ua503)

The Universal Arm Mount, model 347-UA503, is a mounting clamp for wheelchair accessories designed specifically for attachment of the MYDESC EZ-Removable Arm (see separate entry). This metal clamp block can be used with wheelchair tubing from 0.75 to 1.25 inches in diameter, and provides a 0.78 inch cylinder slot for mounting the EZ-Removable Arm directly to the wheelchair frame. The clamp may be mounted either horizontally or vertically.

Universal Support Arm (Usa) (Model F70660)

The Universal Support Arm (USA), model F70660, is an extension arm for wheelchair accessories that clamps to the wheelchair's tubing. The basic arm is made of telescoping aluminum tubing that allows rotational and axial adjustment. Tube collars clamp by integral locking knobs. Angle adjustments are made at two U-clamp joints. Knobs are also used to lock the holder at any angle. The arm has a camera support with a 1/4-20 thread that fits standard 35mm camera thread wells. Included is a hardware p

Utility Clamp For Wheelchair Accessories (Model H70673)

The Utility Clamp for Wheelchair Accessories, model H70673, is a mounting clamp that attaches to the frame of wheelchairs 7/8-inch in diameter. A thumb screw holds the clamp securely. A parallel hole accepts a 3/8-inch diameter rod, and the set screw is turned with a knurled knob. The clamp is made of ABS plastic.

Velcro Closure Safety Strap For Wheelchairs (Model H70623)

The Velcro Closure Safety Strap for Wheelchairs, model H70623, is a wheelchair seatbelt made of Velcro closure with metal D-ring buckles. The belt is adjustable, washable, and can be sterilized. The strap can be positioned at various heights to insure user comfort and security. A short strap anchors to the wheelchair frame while the long strap adjusts in length. DIMENSIONS: 32 inches long x 2 inches wide.

Velcro Seatbelt Alarm (Models Mdt5500 & Mdt5500L)

The Velcro Seatbelt Alarm is a wandering patient system designed for use by individuals with Alzheimer's disease or cognitive disabilities. This restraint-free seatbelt alarm notifies caregivers when an individual tries to get out of a wheelchair unattended. The seatbelt has a Velcro closure and a self-release pull strap, and mounts directly to the wheelchair frame. When the Velcro on the belt is disconnected, the alarm sounds, notifying the staff that the patient is trying to exit the chair. P

Velcro Style Positioning Belt (Model 90133115)

The Velcro Style Positioning Belt, model 90133115, is a wheelchair seat belt designed for use by individuals with mobility and lower extremity disabilities or spinal cord injury. This belt is made of adjustable nylon webbing with a Velcro fastener, and mounts to the chair back at waist level. The attaching hardware is included. DIMENSIONS (LxW): 48 x 2 inches.

Velcro Wheelchair Straps (Models 107, 109, & 700)

Velcro wheelchair straps. 4 inches wide, various lengths. Constructed with stainless steel cinch ring and metal grommet for chair attachment. Includes storage feature for when not in use.

Walking And Wheeling

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: To allow a child to be securely fastened in a wheelchair with an adapted sleeve covering the seatbelt, making it difficult for the child to unfasten the seatbelt.

Weatherbee Power Chair Cover

The WeatherBee Power Chair Cover is designed to protect powered wheelchairs from dust or moisture during transport or storage. To use, slip the cover over the wheelchair and secure underneath using the locking drawstring. Grommets are also provided for additional fastening. The cover is available in standard or heavy-duty models. SIZES: Regular, large, extra large, or tall. DIMENSIONS(HxWxL): The regular cover is 38 x 18 x 44 inches. The large cover is 38 x 23 x 44 inches. The extra large cover

Weatherbreaker, The

The WeatherBreaker is a canopy for scooters designed to protect individuals who use scooters from the weather. This canopy is available in standard, vented, and maximum protection styles. The standard model is made of solid fabric. The vented model has mesh material on the sides and back instead of solid fabric to provide more ventilation for heat protection while still sufficiently protecting from sunlight and rain. The maximum protection model is the same as the vented model with the addition

Wheelblade Xl

Wheelblades, which resemble mini skis, are designed to be locked onto the front wheels of a wheelchair to spread weight over a greater surface area covered with snow. Wheelblades contact surface distributes the wheelchair driver’s pressure evenly onto the ground and prevents the small front wheels from sinking into the snow. The blades run over the ground with very little pressure and have no problem smoothing out rough spots. Two tracking channels on the Wheelblades underside compress the snow

Wheelchair / Walker Pouch (Model 16C002)

The Wheelchair / Walker Pouch, model 16C002, is a wheelchair side pouch and a carrying bag for walker designed for use by people with balance, lower extremity, mobility and walking disabilities, spinal cord injury and others who use a walker or wheelchair. Made of leatherette material, this pouch features a single pocket for storage of magazines or other small items. The pouch attaches over a cross bar and is held in place with dome snaps. The pocket fastens with Velcro closure. DIMENSIONS (LxW)

Wheelchair Belt (Models Mdt825090 & Mdt825091)

The Wheelchair Belt is a wheelchair seatbelt designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. This belt can be permanently attached to a wheelchair or geriatric chair without the use of tools. The belt is made of durable, latex-free nylon webbing with a hook and loop closure (model MDT825090) or a quick release buckle (model MDT825091).

Wheelchair Bike, The

The WheelchairBike is a cycle attachment for wheelchairs designed for use by individuals with mobility disabilities. This maintenance-free wheel and pedal assembly is intended for use by individuals with limited or no use of their legs, attaches to the front of most 18- and 20-inch wheelchairs, and can be maneuvered by shifting body weight. The unit has a steel frame, no wearable parts, and wheels that roll on high-speed bushings. WEIGHT: 16 pounds. GUARANTEE: Lifetime guarantee.

Wheelchair Blanket With Pockets -- Non Slip -- Burgundy

The Wheelchair Blanket with Pockets – Non-Slip is a blanket designed for those who use a wheelchair. Two side pockets and one middle pocket. Hook and loop tabs to keep blanket securely attached. 95 percent polyester, 2 percent nylon.

Wheelchair Camera Mount

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom wheelchair camera mount for a photographer with hemiplegia related to stroke and limited use of his right arm. This individual cannot simultaneously hold his camera firmly and press the shutter, particularly as he uses large lenses which are quite heavy, and using a tripod to hold the camera doesn’t work either, as it’s difficult to set this up with one hand. Therefore, a custom adaptation solution of creating a wheelchair camera m

Wheelchair Canopy

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To provide a custom adapted wheelchair canopy to be used by an individual with light sensitivity and mobility disabilities on her wheelchair and also be portable to fit on public vans, buses, and/or taxis. The canopy is designed to work on almost any wheelchair/cart and be capable of travel. Windows could be added for those more interested in rain and snow protection. The frame is made from steel and aluminum tubing. Scaled drawings are available upo

Wheelchair Cover.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Absorbent terry cloth seat cover for wheelchair. Use towel 40 by 24 inches. Fold towel in half widthwise right sides together. Stitch 1/2 inch from foldline to form casing. Thread twill tape through the casing to tie behind chair. More twill tape and snaps are used to secure the cover to the chair. Includes picture. SKILLS REQUIRED: sewing. AUTHOR: Kernaleguen, A. TITLE: Clothing Designs for the Handicapped. REF: Book: University of Alberta Press, Albe

Wheelchair Dust Covers (Models F70651-0036 & F70651-0048)

The Wheelchair Dust Covers are clear vinyl covers with cotton bindings designed to protect chairs from dust and dirt when not in use. DIMENSIONS: Model F70651-0036 is 36 x12 x 36 inches; model F70651-0048 is 34 x 12 x 48 inches. Any size of cover can be made to order.

Wheelchair Four Point Seat Belt - Auto Buckle (Models 16C138S, 16C138M & 16C138L)

The Wheelchair Four Point Belt Seat Belt - Auto Buckle, models 16C138S, 16C138M & 16C138L, is a wheelchair seatbelt designed to provide security and positioning assistance for wheelchair users and those suffering with posterior and anterior pelvic tilt, and pelvic rotation and thrusting. Designed with 2-inch webbing with fastening tabs for mounting, this belt is equipped with a center pull and four point secondary straps for preventing shifting during thrusting, wiggling, or sliding movement

Wheelchair Fx Wheelchair Light Kits

Wheelchair FX Wheelchair Light Kits are wheelchair lights designed for use by individuals with mobility disabilities. A Basic Safety kit and two Red-White-And-Blue kits are available. The Basic Safety kit includes five extremely low draw LED light strips: two for the armrests, one for the back of the frame, and two for under each seat corner. The Red-White-And-Blue kits include an additional strip for the back plus one for the front, along with LightingFX, a on/off remote control with multiple f

Wheelchair Glider

The Wheelchair Glider is a rocking or glider platform for a manual wheelchair that is designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use a wheelchair. A person in a wheelchair rolls onto the platform using it spring-loaded ramp system, and he or she is able to glide (move horizontally forward and backward) by holding onto handles on each side of the plat form and pushing or pulling. If the user does not have use of his or her ar

Wheelchair Gloves (Model 70628)

Wheelchair Gloves, model 70628, are push gloves made of leather. The gloves cover the palm and back of the hands leaving fingers exposed. The leather attaches around the hand with Velcro closures. Sold in pairs.

Wheelchair Gloves (Model Wc100)

The Wheelchair Gloves, model WC100, by Hatch are push gloves designed for manual wheelchair users. The gloves have no fingers; they are cut to cover the hand up to just below the finger joints. A half sleeve covers the thumb, and the wrists are fully covered with a wide cuff. The gloves open completely at the wrist with velcro closures allowing them to be easily slipped on and off.

Wheelchair Heater

DO IT YOURSELF PURPOSE: To provide warmth for a powered wheelchair user. A small blower-style heater can be purchased from the the automotive department of local discount or automotive supply stores.The heater is generally used to provide supplemental heat or to defrost windows in cars. The model chosen has a fuse rated at 15 amps to allow it to be run using a 12-volt converter on a powered wheelchair. This heater uses a squirrel-cage blower that draws air in the bottom and expels warmed air o

Wheelchair Lifter.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Wheelchair lifter permits servicing of wheelchair wheels, tires, bearings and belts without requiring the occupant to get out of the chair. Describes a lifter which can lift one side of a wheelchair about an inch off the ground. Includes drawing. COMMENTS: For information contact: Jim Anderson, Palo Alto Veterans Administration Medical Center, Rehabilitation Research Development Center, 3801 Miranda Avenue, Palo Alto, California 94304. AUTHOR: Gugerty,

Wheelchair Push Gloves (Model 16C017A)

The Wheelchair Push Gloves, model 16C017A, are push gloves designed for use by individuals with lower extremity or mobility disabilities, spinal cord injury, and others who use manual wheelchairs. Made with suede palms and mesh backs, these bicycle-style push gloves are designed to help protect the hands from blisters and injury while propelling a wheelchair. The open mesh back allows for ventilation while the padded palm area is durable and has a no slip grip. The gloves have open fingers, a ha

Wheelchair Push Handle Extensions

CUSTOM ADAPTATION PURPOSE: To enable a tall parent to push a child's wheelchair. The existing push handles were sawed off a wheelchair and new ferrules were fixed inside the exposed tubes with Loc-tite. Two new longer L-shaped handles were made of metal and one end of each was afixed in the new ferrules. The handles were finished by painting them red to match the rest of the chair and attaching bicycle-style rubber handgrips. TITLE: Bicycle and Beyond. JOURNAL: TAD Journal. REF: Volume 26, Num

Wheelchair Push Handle Extensions For Tall Person

CUSTOM ADAPTATION PURPOSE: To enable a tall caregiver to safely push a wheelchair. Designed to work with a variety of wheelchairs and to be removable for use on multiple chairs, a set of tubular steel extension arms with handgrips at the top was fashioned. The extensions are adjustable and hook to the chair frame at the bottom. The height of the handles can be adjusted using wing nuts on the verical uprights and the width between the handlebars is adjustable using a wing nut on the horizontal b

Wheelchair Safety Alarm

The Wheelchair Safety Alarm is designed to help caregivers keep track of the disabled love one. It sounds an alert as soon as the individual lifts themselves out of their wheelchair. Covered in waterproof vinyl. Can be used by other chairs as well. The pressure pad connects to the audio alarm. The alarm has an On/Off switch and battery warning.

Wheelchair Safety Belt

The Wheelchair Safety Belt is a wheelchair seatbelt designed to prevent falls from wheelchairs. The adjustable, heavy-duty Velcro belt crosses the lap and attaches to the wheelchair axle with reinforced grommeted nylon straps. SIZES: One size fits most.

Wheelchair Seatbelt (Models 6880 & 6886)

The Wheelchair Seatbelt is a belt restraint designed to keep individuals in wheelchairs from falling forward out of the chair. It can be permanently attached to the upholstery screws and has a Velcro closure. DIMENSIONS: Both models are 2 inches wide; Small (6880) is 32 to 42 inches long, Large (6886) is 42 to 52 inches long.

Wheelchair Seatbelt Sleeve

---- “DO IT YOURSELF” ENTRY --------- PURPOSE: To create a “sleeve” to fit over a child’s wheelchair seatbelt, making the belt safer and harder to undo. First, lay material on flat surface with back side facing up; using straight pins, pin edges together lengthwise along material. Second, using a sewing machine or needle; stitch along line lengthwise. Third, turn material right side out and slip onto one end of wheelchair seatbelt. Fourth, fasten the belt and slide material over fastener; scrun

Wheelchair Umbrella

The Wheelchair Umbrella is an umbrella designed to provide rain and sun protection for wheelchair users. Designed to fit most wheelchairs, this umbrella has a fully adjustable stem that mounts onto the chair’s push handle. DIMENSIONS (LxD) 36 x 40 inches. COLOR: Blue and white.

Wheelchair Umbrella

The Wheelchair Umbrella is designed to provide shelter from the elements for wheelchair users. The umbrella is made of a vinyl tent mounted on a frame which folds down behind the chair. Clear plastic windows provide visibility when the tent is up. The unit mounts to the wheelchair frame in four locations. PROTOTYPE DEVELOPMENT: Designed by Dave Doman for wheelchair users to allow them to quickly employ a cover in the event of rain without worrying about getting raingear caught in the wheels of

Wheelchair Waist Belt With Buckle

The Wheelchair Waist Belt With Buckle, model MDT825120, is a wheelchair seatbelt designed for use by individuals with mobility disabilities or spinal cord injury. Made of washable nylon, this latex-free belt circles the waist, passes through a slide buckle, and ties in back. The slide buckle allows for individual fit and prevents overtightening. SIZES: One size fits all.

Wheelchair Y Safety Belt (Model 6038)

The Wheelchair Y Safety Belt is a belt restraint or wheelchair seatbelt. The "Y" shape is designed to prevent slumping and sliding of individuals in wheelchairs. The belt is completely adjustable and made of nylon webbing. SIZES: One size fits all.

Width Varying Device For Wheelchairs.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Narrowing wheelchairs for doorway access. The device can be mounted on any size wheelchair with a folding crossbrace. Does not interfere with folding the chair. Can be installed for right or left hand use. Only two fingers needed to activate switch. A geared low speed motor is mounted on one side of the chair frame. A strap is attached to the opposite side of the frame and to the motor pulley. Pressing the switch operates the pulley to pull the sides o

Wijit

The Wijit is a wheelchair lever drive and braking system designed for use by individuals with mobility disabilities. The system includes a lever that attaches to each drive wheel of most manual wheelchairs, enabling the user to propel the chair using a pumping motion. The levers can be switched to reverse mode to enable the user to reverse directions. To engage the braking system to reduce speed or stop, the levers are simply pushed forward toward the body.

Wunderglow Wheelchair Light System Kit

The wUnderglow Wheelchair Light System Kit is a wheelchair light set designed for use by individuals who use wheelchairs. The set includes two micro lights and a mounting clip. The white light increases visibility and the multi-colored light can be used to increase visibility or strobing for visibility and effect. The clip rotates 360 degrees to enable the user to select precise positioning. POWER: Uses two replaceable CR 2016 lithium batteries in each light. OPTIONS: Second clip to enable both

X-Fer Rail Portable Transfer Rail

The X-Fer Rail Portable Transfer Rail is a transfer board for designed for caregivers to use with individuals with mobility difficulties. Enables safe transfers to and from a wheelchair. Quickly folds and unfolds. Conveniently fits in a backpack, wheelchair bag, carry-on or briefcase (not included). Portability of the board promotes use outside of the home which will help to reduce shoulder strain associated with independent transfers. Open seating design reduces the risk of friction based skin

 
Processing...


Driving Walking/Biking Public Transit  Get Directions